One. How is a complete wardrobe installed?
1、Place a protective pad on the floor. Begin assembly from one end, starting with the wider side panel. Lay the wider side panel flat on the floor (with a 700mm clearance from the back wall). First, place the three-in-one plug panel, which has been pre-filled, on the protective pad. Check that the hole spacing matches the drawing, and install the three-in-one single linkage. Then, attach the solid wood dowel to the wider side panel, with the top of the dowel facing up, and the remaining solid wood dowels facing down. The large hole of the support should face inward (the middle support should be at the same height as the L-shaped shelf, i.e., the space between the bottom and the support should be 960mm. Drill holes in the support panel on site). Place the side panel and attach the solid wood dowel, ensuring that the dowels connect the two sides. Install the double linkage on the second support panel, noting that the large hole on the double linkage can only lock half of it (90°). once both support panels are fixed to the side panel, tighten the large linkage simultaneously.
2、Back Panel Installation: Place the assembled cabinet side on a leveled, padded surface. Ensure the side panel is flat and uniform. Measure the diagonal dimensions of the cabinet with a ruler and adjust them to be equal. Begin installing the first back panel starting from the wider edge, and if there are studs in the middle, draw a centerline with a pencil before driving in the nails.
3、Installation of L-shaped Shelf: Align the side of the L-shaped shelf with a parallel line on the corresponding side panel, then lift it up 9mm and draw three central lines for the adhesive beads. Align the top edge of the L-shaped shelf with a parallel line on the corresponding bottom panel, and draw three central lines for the adhesive beads within the line. Use a 10mm drill to create holes, with a depth of 10-20mm. Install the single pole. After installing the L-shaped shelf, nail it to the back panel for fixing.
4、Install three-section track：Secure the track to the drawer.，Bring it flush with the drawer floor.。Install the parent rail and secure the sub-rail on the sub-rail's vertical guide.（Adjustable）。Increase the distance between drawer panels and the center of the drawer track.2mmGaps。Remove the main rail，As needed，On the cabinet side.90°Draw cross-sections using a protractor.，This cross-section represents the center line of the parent rail.。Drawer panel: vertical alignment，Enter from the service area, outside the cabinet wall.19mm，Draw a cut line。Align the main track with the cut line.，Central axis aligned with the cross-section，Secure the screw to the terminal's crossbar.（Adjustable）。once placed in a drawer，Adjust parameters for optimization.，Ensure drawer surfaces are smooth.，Average gap in the vicinity。Finally，On the lateral view of the tooth.、Secure screws on the guide rail's vertical slots.。Install the next one following this procedure.。If the drawer is completely full.，Apply the same principle to install sequentially from bottom to top.。The top drawer can be used.90°Fixed rate。Drawer surfaces should be flush.，Average gaps。Gap between drawers is2mm。
5、Grid Shelf Installation: Install the three shelf rails just like installing the three rails for the drawer slides. Measure the gap between the side panel and the center of the rail, adding a 50mm gap, and mark this measurement on the side panel of the cabinet. Install the main rail and perform testing and fixing. Ensure a 50mm gap at the top of the side panel of the grid shelf to facilitate easy access.
6、Installation of Pant Racks: Similar to the installation of grid racks, but with a 20mm gap between the side panels of the pant racks and the surface of the grid rack. Maintaining a 20mm space is also for ease of use.
7、Sliding Door Installation: Install the three sliding door tracks onto the sliding door. The sliding door height is typically 1700mm above the base layer (customer may specify a different height). Using a 90° angle ruler, mark the horizontal cut lines for the tracks on the side panel at the required height. Measure the parallel distance between the new eyes on the three sliding door tracks and record the precise data. Then, using a 90° angle ruler, draw the horizontal cut lines for the lower tracks on the side panel. Install the upper and lower sliding door tracks, ensuring the spacing between the tracks and the back panel is 5mm.
8、Installation of the "Yi Tong" component: Draw a horizontal cut line 38mm below the ground-level solid layer, and a vertical cut line on the side panels, with the central position of the first eye of the "Yi Tong" component located above the cross support.
Two. important considerations for installing complete wardrobes.
Before installing custom cabinets:
1. Inspect the packaging to ensure it is intact and undamaged. If there are any damages, the installation personnel should open the package and check the interior for any signs of damage, such as dents or scratches, on the furniture.
2. If any issues arise, it is crucial to promptly communicate with the vendor's after-sales service personnel and have the installation team verify the situation to protect your own interests.
3. After opening the package, inspect the received products for any discrepancies in appearance or color that may not conform to your order requirements. This is a common issue, such as incorrect colors from the manufacturer, or pre-installed furniture that does not match the customer's specifications. This can result in significant losses for both parties.
4. If there are any glass or plastic products, check for any signs of breakage or deformation.
Custom closet installation:
During installation, various unforeseen issues may arise. Therefore, it is important to pay attention to several key points:Generally, flat-panel furniture (typically consisting of simple wooden panels without any decorative elements) can be DIY installed. However, this is only suitable for small items such as small shoe cabinets and small sitting platforms. Large furniture, solid wood furniture, or furniture with complex designs, such as large wardrobes and entrance cabinets, are not suitable for DIY installation.
1. During installation, pay attention to protecting other areas of the house. Furniture is typically installed last, and cleaning should begin after the installation is complete. Pay particular attention to: flooring (especially hardwood flooring), doors, door frames, wallpaper, stairs, and wall lights.
2. Personally supervise the installation process to ensure there is no damage, which is not a major concern as the installers are experienced and careful. Any damage to furniture will result in appropriate penalties.
3. Installation of hardware, such as handles and knobs: This primarily involves determining the optimal installation location for the best user experience, prioritizing functionality over aesthetics. For example, handles for cabinets or raised cabinets should always be installed on the lower side, while handles for base cabinets, desks, and small cabinets should be placed on the upper side.
4. Pay attention to cleanliness: This is particularly important when replacing old furniture. Since custom-made cabinets differ from standard furniture, many parts are installed in your home, which inevitably involves drilling and cutting, leading to the generation of sawdust and dust.
5、Wall-Mounted Fixtures: Electrical and plumbing modifications are now essential components of modern renovations. Therefore, there may be fixtures and pipes embedded within the walls and at the junctions between the ceiling and the wall. Installing custom cabinets and integrated kitchen cabinets is similar to installing standard cabinets, and may require heavy equipment such as electric drills. If the location of the fixtures and pipes is not known in advance, there is a risk of damaging the wiring or water pipes, which can make subsequent repairs difficult.
After custom wardrobe installation:
1. Verify that the overall construction meets the design specifications, including whether the internal layout aligns with the floor plan, and whether there are any surface scratches or damage.
2、Inspection details: such as checking for missing hardware, verifying smooth operation of doors and windows, and inspecting gaps between different designs.